Mixer Blade Coating and Refurbishment

We renew worn turbo mixer blades, impeller sets and cooler paddles and can add an optional tungsten carbide coating, for all blades whether or not Erk made them.

Illustration of a worn and a refurbished, coated mixer blade, before and after

Highlights

01

For all makes

All blades are renewed, whether or not Erk made them.

02

Tungsten carbide coating

Optional coating for abrasive recipes.

03

Renew or replace?

We look at the blade and choose the best route with you.

04

New blades ready too

If needed, new AISI 304 blades, usually from stock.

What is mixer blade refurbishment?

Turbo mixer blades wear over time. Edges become rounded, wings get thinner and the impeller no longer moves the material as well as it did on day one. That does not always mean buying new blades: our mixer blade refurbishment service makes your worn blade usable again, and we can add a coating if you wish.

Refurbishment and coating are available for all blades, whether or not Erk made them. This covers heating turbo mixer impellers, bottom and upper blades, cooling mixer paddles and blades from mixers of other manufacturers.

Refurbishment lets you reuse a worn blade instead of scrapping it. In plants with more than one mixer especially, having replaced sets refurbished and keeping them as spares makes maintenance planning easier. We judge together whether refurbishment suits your blade by looking at where and how far it has worn.

Tungsten carbide coating

Blades can be given an optional tungsten carbide coating. Tungsten carbide is a wear-resistant coating material, chosen especially to protect blade edges in abrasive recipes with a high calcium carbonate content. The coating can be applied to renewed blades and to new ones. We assess at quotation stage whether it suits your recipe; not every recipe needs it.

Refurbish or replace?

Which route fits depends on the blade's condition and your needs. We decide together once we have seen the blade or its photos:

Situation

Usually the right choice

Blade body sound, wear on the edges

Refurbishment, optional coating

Abrasive recipe, edges wear quickly

Refurbishment or a new blade, with tungsten carbide coating

Blade broken, cracked or very badly damaged

New blade

Recipe has changed and needs a different geometry

New blade with the new geometry

A part is needed straight away

New blade (usually from stock)

Our new blades are made of AISI 304 stainless steel, supplied balanced and usually delivered from stock, otherwise within 1–2 weeks. For details see turbo mixer impeller and cooling mixer paddles.

Which blades do we refurbish?

Knowing which mixer and which recipe the blade runs with matters for the coating decision and the scope of the refurbishment, so please mention both in your request.

How it works

  1. Send photos and information: photos of the worn blade and the mixer's make and model; for Erk mixers, the serial number.
  2. Assessment: from the photos we decide together whether refurbishment or a new blade fits, and whether coating is needed.
  3. Quotation: we quote the route you choose.
  4. Getting the blade to us: for refurbishment the blade is sent to us.
  5. Refurbishment and coating: the blade is renewed, coated if requested, and sent back to you.

What to send us

Information

Why

Close-up photos of the worn areas

To see where and how far it has worn

A photo of the whole blade (with a tape measure)

For scale and overall condition

Mixer make and model; serial number for Erk mixers

To know which mixer the blade runs in

Recipe type and filler content

To assess whether coating is needed

Is it time to refurbish?

Wear depends on the filler (calcium carbonate) content of the recipe and the mixer's running hours. Longer heating or cooling times, a change in dry blend quality or bulk density, more vibration and visibly rounded blade edges show it is time. We explain how to monitor wear in mixer blade wear.

Fitting a refurbished blade

A refurbished blade should be fitted as carefully as a new one. Make sure the hub sits cleanly on the shaft and that all fasteners are present. If only part of an impeller set was renewed, check the other blades for wear too; blades with different wear running together can affect balance. After fitting, watch the mixer for vibration and noise on the first run and note the heating time of the first batches. Our service team can support these steps remotely or on site.

Does every recipe need coating?

No. Coating makes sense in abrasive recipes where blade edges wear quickly, for example rigid PVC recipes with a high calcium carbonate content. In recipes with little filler an uncoated blade is often enough. Share your recipe and filler content, and we will assess together whether coating would benefit you.

A spare set to cut downtime

To keep the mixer running while blades are being renewed, we recommend keeping a second set: one set runs while the other is refurbished. Taking a new set from stock and sending the worn one for refurbishment makes planned maintenance easier.

For all blade options, go back to our mixer blades page.

Papenmeier and Henschel are trademarks of their respective owners; Erk PVC Makine is not affiliated with these companies. The names are used only to indicate compatibility.

Send us photos of your worn blade, and we will quickly quote refurbishment, coating or new blades.

Downloads

Frequently Asked Questions

Do you also refurbish blades not made by Erk?

Yes. Refurbishment and coating are available for all mixer blades, whether or not Erk made them.

What coating do you apply?

An optional tungsten carbide coating. It is chosen especially for abrasive recipes with a high calcium carbonate content; we assess together whether it suits your recipe.

Can my blade be refurbished, or do I need a new one?

It depends on its condition. Blades with a sound body and wear on the edges can usually be refurbished; for broken, cracked or badly damaged blades we recommend a new blade. We decide together once we have seen the photos.

Can new blades be coated too?

Yes. The tungsten carbide coating can be applied to renewed and new blades as an option.

Does my mixer have to stop during refurbishment?

Not if you have a second set of blades: one set runs while the other is refurbished. New blades are usually delivered from stock, otherwise within 1–2 weeks.

What should I send for a quote?

Close-up photos of the worn areas, a photo of the whole blade with a tape measure next to it, the mixer's make and model (the serial number for Erk mixers) and your recipe type.

Related Products

Get a Quote

Request a Quote

Fill in the form and our sales engineers will get back to you within one business day.